JNTU
JNTU B.Tech II KINEMATICS OF MACHINERY Previous Question Paper (December - 2017 - R15)
Note: This question paper contains two parts A and B. Part A is compulsory which carries 25 marks. Answer all questions in Part A. Part B consists of 5 Units. Answer any one full question from each unit. Each question carries 10 marks and may have a, b, c as sub questions.
PART- A
Define mechanical advantage and transmission angle of a mechanism.
Answer
Mechanical Advantage is the ratio of the output force or torque to the input force or torque in a mechanism. The Transmission Angle is the acute angle between the output link and the coupler link in a four-bar mechanism; it determines the efficiency of force transmission.
What is a kinematic pair? Classify kinematic pairs according to nature of relative motion.
Answer
A Kinematic Pair is a joint of two links having relative motion between them. They are classified by motion as:
- Sliding pair (relative sliding)
- Turning pair (relative rotation)
- Rolling pair (relative rolling)
- Screw pair (turning and sliding)
- Spherical pair (three-dimensional rotation)
Name all the inversions of slider-crank mechanism with one application for each Inversion.
Answer
Sign in to view the complete answer paper.
Briefly explain about coriolis acceleration component.
Answer
Sign in to view the complete answer paper.
What is scott-russel mechanism? What is its limitation?
Answer
Sign in to view the complete answer paper.
Briefly explain Ackermann steering gear.
Answer
Sign in to view the complete answer paper.
Define base circle, pitch circle and pressure angle for cams.
Answer
Sign in to view the complete answer paper.
What is undercutting in cams? Explain.
Answer
Sign in to view the complete answer paper.
What type of gears are used for intersecting shafts? Explain.
Answer
Sign in to view the complete answer paper.
What is the difference between simple and compound gear trains?
Answer
Sign in to view the complete answer paper.
PART- B
What are the inversions of a four bar chain? Explain in detail.
Answer
Sign in to view the complete answer paper.
A crank-rocker mechanism has a 60 mm fixed link, a 30mm crank, 50mm coupler and a 60 mm rocker. Draw the mechanism and determine the maximum and minimum transmission angles.
Answer
Sign in to view the complete answer paper.
What are different types of constrained motion? Explain them in detail.
Answer
Sign in to view the complete answer paper.
The length of a fixed link of a crank and slotted-lever mechanism is 250 mm and that of crank is 100 mm. Determine the Inclination of the slotted lever with the vertical in the extreme position and also find the quick-return ratio.
Answer
Sign in to view the complete answer paper.
Define instantaneous centre of rotation. State and prove Kennedy’s theorem as applicable to instantaneous centres of rotation of three bodies.
Answer
Sign in to view the complete answer paper.
In a slider crank mechanism, the lengths of the crank and the connecting rod are 200 mm and 800mm respectively. When the crank has turned 30° from its inner dead centre and it rotates at 40 rad/sec, find the velocity of slider.
Answer
Sign in to view the complete answer paper.
For the configuration of a slider-crank mechanism shown in the figure 1, calculate the:
- Acceleration of the slider B
- Acceleration of the point E
- Angular acceleration of the link AB, OA rotates at 20rad/s CCW.
Answer
Sign in to view the complete answer paper.
Enumerate straight-line mechanisms. Why are they classified into exact and approximate straight-line mechanisms? Sketch all the mechanisms.
Answer
Sign in to view the complete answer paper.
Sketch a paucellier mechanism. Prove that it can be used to trace a straight line.
Answer
Sign in to view the complete answer paper.
What is an automobile steering gear? What are its types? Which steering gearing is preferred and why?
Answer
Sign in to view the complete answer paper.
Derive an expression for the ratio of angular velocities of the shafts of a hooke’s joint.
Answer
Sign in to view the complete answer paper.
Draw the profile of a cam operating a knife-edge follower having a lift of 30 mm the cam raises the follower with SHM for 150° of the rotation followed by a period of dwell for 60°. The follower descends for the next 100° rotation of the cam with uniform velocity again followed by a dwell period. The cam rotates at uniform velocity of 120 rpm and has a least radius of 20mm.
Answer
Sign in to view the complete answer paper.
What is a follower? Discuss about different types of followers.
Answer
Sign in to view the complete answer paper.
Deduce the expressions for the velocity and acceleration of the follower when it moves with simple harmonic motion.
Answer
Sign in to view the complete answer paper.
Discuss the various terms used in gear terminology and explain them with a neat sketch.
Answer
Sign in to view the complete answer paper.
Derive expressions for arc of contact of pinion and gear with a neat sketch.
Answer
Sign in to view the complete answer paper.
What is meant by interference in involute gears? Explain.
Answer
Sign in to view the complete answer paper.
Below figure 2 shows a gear train in which gears D-E and F-G are compound gears. D gears with F; and G gears with C. the numbers of teeth on each gear are A=30 B=120, C=135, D=30, E=75, F=30, G=60. If the wheel A is fixed and the arm makes 20 revolutions clockwise, find the revolutions of B and C.
Answer
Sign in to view the complete answer paper.